For your 2011 Ford Crown Victoria we have universal trailer wiring harnesses that are a fit, but not the part # C55326 that you mentioned.
The best solution is the part # 119250KIT which installs without requiring any splicing into the vehicle wiring. Or for a lower cost option that would be a bit more involved to install we have the part # C59496. view full answer...
I did not know that having a sagging back end was cause to be pulled over. I know that some areas do have restrictions on how far off the pavement a vehicle can be. So first lets look at why the vehicle is sagging. If there is nothing in the trunk or back of the vehicle to weigh it down, and you have not modified it (like cutting the springs or used a lowering kit) then there is probably a problem with the suspension.
If your 2000 Ford Crown Victoria uses rear air shocks, that could be... view full answer...
I have another option for you, but the Curt Multi-Fit Trailer Hitch Receiver # C13900 you were looking at is not confirmed to fit your 2007 Ford Crown Victoria Police Interceptor.
Instead I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # 13707 which is confirmed to fit your vehicle, and is a great option for carrying a bike rack like the Thule Hitching Post Pro # TH934XTR, a cargo carrier, or even light duty towing. You will need to drill a few holes in the vehicle... view full answer...
The only option we have for trailer wiring for your 2004 Ford Crown Victoria is a hardwire option like part # 46255.
Or if you didn't want to splice any wires into your vehicle taillights you could use the zero contact kit part # 119250KIT that uses sensors to detect the vehicle taillight wiring instead of having to splice into them. You will still need to run a power wire up to the vehicle battery though. view full answer...
You would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the part # TK63VR. This is one our best selling brake controller because of how well it works and how easy it is to setup. It's also priced great too. view full answer...
My trailer hitch recommendation is the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2", part # 13707. It has a maximum tongue weight of 400 lbs and a maximum gross trailer weight of 4,000 lbs, which is greater than our other trailer hitch options for your 2009 Ford Crown Victoria.
I have included a product description link and a video of this trailer hitch being installed on a 2007 Ford Crown Victoria below. view full answer...
The Draw-Tite Max-E-Loader Trailer Hitch Receiver part # 41116 is a great option for a 2009 Ford Crown Victoria and what I recommend using. It will fit models with dual exhaust. There are extra steps in the instructions for for fitment on these models. view full answer...
We have a trailer wiring kit that was confirmed as a fit for your 2007 Ford Crown Victoria with the part # C59236 and allows you to run a wire to the battery and is confirmed to fit with your 2-wire setup. view full answer...
I'd recommend using a powered converter due to the circuit protection it'd offer to the wiring of your car. The # 119178KIT would be an excellent choice.
If you click the provided link, you can see the wiring harness being installed on a 2003 Crown Vic. view full answer...
With a Crown Victoria, there will be enough weight pressing down on the front tires that you should not need them up front. But, since the Crown Vic is a rear-wheel drive car, you will most definitely need them on the rear tires.
We are based in Wentzville Missouri and our only retail store location is here. We do regularly ship to the contiguous 48 states. And can ship to HI, AK and PR. view full answer...
Both the Hopkins # 46255 and # HM46155 Wiring Harnesses that you referenced will technically work on your 2003 Ford Crown Victoria P71 but the better option is with the # 46255. In addition to the powered converter that's needed to both combine the separate signal circuits on the Crown Vic to be compatible with trailer wiring and provide sufficient power to the trailer lights, it also includes a fuse holder and fuse along with additional wire to run the converter's power lead up to the... view full answer...
First you will need to verify the towing capacities of the 2009 Ford Crown Vic by checking the owners manual. If you already have a trailer hitch then make sure it is rated for use with weight distribution. There should be a sticker on the hitch that lists the capacities using weight distribution if the hitch is compatible. If it is not then you would want to add a different hitch such as # 13707.
This hitch is rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight or... view full answer...
You would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. view full answer...
First, you are going to want to make sure that the hitch is rated for use with weight distribution. Not all hitches are. There should be a sticker on the hitch that will indicate its capacity when using weight distribution. You have to do the same for the vehicle by consulting the owners manual.
If you need a hitch that is rated for weight distribution you can use # 13707. I have included a link to a video showing a typical installation and a link to the instructions.
For weight distribution... view full answer...
I wish I could tell you which specific wire color you'd need to find on your 2011 Ford Crown Victoria but we haven't had the chance to install a brake controller on it so what you'll need to do is use a circuit tester like part # PTW2993 to test all of the wires that lead to the brake switch till you find the circuit that only has voltage when the brakes are applied. That's what you'll use to connect to the red wire of your brake controller.
I attached a help article on installing brake... view full answer...
The Draw Tite hitch part # 41116 is a confirmed fit for your 1996 Mercury Grand Marquis. For a ball mount you'd need the part # 36063, for a 1-7/8 inch hitch ball part # 19257, for 2 inch ball part # 19258, then for trailer wiring # C59236. view full answer...
For your 2003 Ford Crown Victoria I recommend the Curt hitch # 13707. This is a Class III hitch with a 2 inch receiver rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight so it covers the capacity of the vehicle.
Because your Crown Vic has dual exhaust there is some slight modification to the exhaust that will be needed to install this or any hitch for the vehicle. Its actually not all that difficult and I have included a link to a video showing an example installation... view full answer...
For your 2003 Ford Crown Victoria P71, which is the Police Interceptor model, you will need the Hopkins Universal Install Harness # 46255. This hardwire kit includes everything needed to install a 4-Way trailer connector on the vehicle.
The Hopkins Plug-In Simple Wiring Harness # HM11140504 that you mentioned unfortunately will not work on Crown Victorias equipped with the Police Package. There is not a custom harness like this available for this particular model. view full answer...
The brake controller that we recommend the most is the Tekonsha Prodigy P2 Brake Controller # 90885. This proportional brake controller is one of our best selling brake controllers because of how easy it is to use and how well it works.
A 7-way will have to be installed in order for the brake controller to be functional. But before you install a 7-way you will need a 4-way.
For a 4-way you will need a Tow Ready Custom Fit Vehicle Wiring Kit # 119179KIT. I attached installation instructions... view full answer...
The trailer hitch that fits your 2011 Ford Crown Victoria that has the highest towing capacities and would work great for towing your Integra would be the Curt hitch part # 13707. This can tow up to 4,000 lbs which would easily be enough for a lightweight Acura Integra. I attached an install video for this for you to check out as well.
For trailer wiring you'd also want the # C59236. view full answer...
Go To Results